ようこそ!R/C Web Shop Kb へ
キーワードを入力 
商品カテゴリ
-
人気ランキング




商品名

FrSky 2.4G TFR4 4ch RX

価格

3,280 円 [消費税298円込み]

在庫

在庫有り

タイプ
商品説明 FrSky社の TFR4 2.4G 4ch受信機となります。

メーカーサイトはこちら。


1.Introduction
1.1 Compatibility:
FASST 2.4G: Air Systems (7CH Mode/Multi Mode) & Surface Systems (C1 Mode)
FrSky TF Modules: TF-8M, TF-14M
1.2 Specifications:
Number of Channels: 4
Operating Voltage Range: 3.5V~10V
Operating Temperature Range: -10℃~80℃
Dimension: 34*19*8mm
Weight: 6.2g
1.3 Features
1) Compatible with FASST 2.4G: Air Systems (7CH Mode/Multi Mode) & Surface Systems (C1 Mode);
2) CPPM and RSSI (PWM) output - If CH3 and CH4 are connected by a jumper, CH1 will output CPPM for CH1~CH8, and CH2 will output RSSI (PWM);
3) Lighter weight and physically smaller;
4) Two selectable failsafe setting options.
2.Setup
2.1 Bind procedure:
Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.
2.2 Setting failsafe:
TFR4 support two selectable failsafe setting options, either use native failsafe position preset on the transmitter side, or set failsafe on TFR4.
2.2.1 Use native failsafe position preset on the transmitter side:
If not disabling failsafe on the transmitter side, TFR4 will use native failsafe position preset on the transmitter side.
2.2.2 Set failsafe on TFR4 side:
TFR4 supports failsafe function for all channels. Follow the steps below to set failsafe on TFR4:
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.
Hint: If not disabling failsafe on the transmitter side, TFR4 will use native failsafe position preset on the transmitter side.
2.3 LED status:
RED LED GREEN LED Mode
Off On Normal mode
On On Waiting to be bound
Flashing On Signal lost
On Flashing twice Set failsafe

3. How to get CPPM and RSSI from TFR4

If CH3 and CH4 are connected by a jumper, CH1 will output CPPM for CH1~CH8, and CH2 will output RSSI (PWM).


※FrSky受信機の動作電圧範囲は広く設定されております。
対応電圧範囲内であれば受信機自体は動作しますが、レギュレータ等は
搭載しておりませんので、電源の電圧がそのままサーボにも供給されます。
ですのでご利用される電源とサーボによってはサーボの動作範囲外になる
可能性もございますのでご注意ください。


※ EXPACK500発送(現行はレターパック500)対象商品です。
※ 当店をご利用される前に必ずこちらをご確認ください。

数量 [半角数字]